[Verkaufe] (( ito )) Produktion Apr-Mai

Diskutiere (( ito )) Produktion Apr-Mai im Gewerbliche Vorstellungen Forum im Bereich Schwarzes Brett; ito ist ein Mikrocontroller mit Solid-State-Relais, Wifi und optionaler on-board 230V-Stromversorgung (Über ito, Video). Durch Aufspielen der...

  1. #1 faustino, 20.03.2019
    Zuletzt bearbeitet: 20.03.2019
    faustino

    faustino Mitglied

    Dabei seit:
    03.03.2010
    Beiträge:
    2.392
    Zustimmungen:
    1.911
    ito ist ein Mikrocontroller mit Solid-State-Relais, Wifi und optionaler on-board 230V-Stromversorgung (Über ito, Video). Durch Aufspielen der freien leva!-Firmware wird ito zum Brühdruck- und Temperaturregler. leva! bringt innovative Funktionen: Perfekte Brühtemperatur (PID), Pressure-Profiling mit Drucksensor, Preinfusion, Dosieren, verkürztes Aufwärmen, Shottimer, Shotzähler, Tanküberwachung, Verkalkungsüberwachung, Energiesparfunktionen uvam.

    [​IMG]
    65x56mm: Weniger Fläche als Kreditkarten

    [​IMG]
    Display (Option) im Deckel einer Maschine; Lasercut.
    SICHTBAR | UNSICHTBAR

    Obwohl leva! sich am besten mit Display bedienen lässt (Drehencoder = Druckregler), ist ein Display nicht erforderlich. Die Konfiguration kann über Wifi erfolgen:

    [​IMG]
    Virtuelles Display (Windows, Linux, Mac OS X, Android)

    Eine Maschine mit leva! kann aussehen, wie vorher. Lediglich ein Drehencoder, der zum Verstellen der Temperatur dezent auf der Rückseite installiert werden kann (nicht muss), deutet dann auf den Umbau hin. Optional kann eine weiße LED für erweiterte Signalisierung in die Originalheizlampe eingesetzt werden.

    Bluetooth Low Energy | Dosieren

    Das optionale Bluetooth-Modul (BLE 5) kann ito mit einer Waage (Skale 2) und anderen Geräten verbinden.

    [​IMG]
    BLE--Erweiterung

    OPTIMIERT FÜR ESPRESSO

    Da leva! für Espressomaschinen entwickelt wurde, ist die Temperaturregelung besser, als mit normalen PID-Reglern: Es gibt eine auf das Flowmeter reagierende Feed-Forward-Komponente, man kann den Brühtemperaturverlauf während des Bezugs programmieren und es gibt parametrierbare Koeffizienten, d.h. der PID kann für spezielle Situationen (Aufwärmen, Standby, Bezug) unterschiedlich konfiguriert werden. Für Anfänger ist Autotuning dabei, welches automatische Einstellungen findet. leva! kann zwei Heizelemente regeln, z.B. Boiler und Brühgruppe, entspricht also zwei PIDs in einem Gerät. leva! enthält eine Druckregelung mit Drucksensor und bietet Pressure-Profiling per Programm, Paddle oder Encoder.

    [​IMG]
    Druckverläufe wie mit Handheblern dank Pressure-Profiling

    SOFTWARE EINSTELLEN BEOBACHTEN VERBESSERN

    Interne Werte werden als Kurven live und drahtlos an Computer übertragen, was die Einstellung zum Vergnügen macht:

    [​IMG]
    Der Statusmonitor zeigt, was passiert - unter Windows, Linux, Mac OS X und Android (Video, Android-App)
    DOKUMENTATION

    leva! ist auf 228 Seiten umfassend beschrieben (Englisch), ito auf 63 Seiten (Englisch).

    [​IMG]
    Anleitungen im Download

    GENAU MIT TSIC

    leva! unterstützt schnell ansprechende TSic-Präzisionstemperatursensoren, die mit 0,1°C auflösen und kalibriert sind. Absoluter Fehler bei 90°C max. 0,3°C - besser als Pt100 DINB. Der Messbereich geht bis 150°C. Zur Befestigung ist Wärmeleitkleber dabei.

    FEATURES IM ÜBERBLICK

    Folgende Tabelle vergleicht leva! mit typischen PIDs:

    [​IMG]

    INTALLATION

    ito wird mit selbstklebenden Füssen installiert. Je nachdem ob leva!u als PID, für Pressure Profiling oder beides genutzt werden soll, ist der Anschluss so einfach wie der üblicher PIDs (4 Kabel am 230V-Kabelbaum umstecken: Stromanschluss und Thermostat) oder deutlich anspruchsvoller. Der Einbau darf nur von qualifizierten Personen vorgenommen werden, die mit Netzspannung umgehen können und die englische Dokumentation verstehen!

    [​IMG]
    Installation mit Klebefüßen und Isolationsunterlage

    [​IMG]
    Im Maschinenraum einer Silvia

    Das optionale Display kann hinter einem Blech mit passendem Ausschnitt (laserteileonline.de, ca. 25€), Alu-Blende nach Maß (Schaeffer AG) oder 3D-Druck installiert werden.

    ANFORDERUNGEN

    leva! kann mit Espressomaschinen genutzt werden, in die grundsätzlich ein PID eingebaut werden kann. Am Einbauort dürfen 60°C nicht überschritten werden (Display 70°C). ito beansprucht mit Füßen 71x62x25mm. Die Kabel sind 40cm lang. Das externe Relais ist 56x41x26mm groß. Es wird per Wärmeleit-Klebepad befestigt. Das Flowmeter hat 41mm Durchmesser. Die Pumpenfunktionen sind für Vibrationspumpen ausgelegt, andere Pumpen sind nicht kompatibel. Pumpende Programme (z.B. Dosieren), funktionieren bei manuell zu öffnenden E61-Hebelventilen nicht. Weitere Anforderungen/Einschränkungen sind der ito-Vorstellung und dem leva!-Manual zu entnehmen. Es wird mindestens einmalig, zum Aufspielen von Firmware, ein Windows/Linux-PC mit Wifi benötigt (Win7 32bit, Win8.1 64bit, Win10 64bit oder Linux Mint 17.3 XFCE; andere Versionen könnten auch funktionieren, wurden aber nicht getestet, so dass dafür keine Gewährleistung übernommen wird). Es wird ein DVD-Laufwerk benötigt. ito ist möglicherweise nicht mit jedem Wifi-Endgerät kompatibel (getesteteter Wifi-Stick: TL-WN722N).

    OPTIONEN ENTWICKELT ZUM ERWEITERN

    Komponenten können nach gewünschter Anwendung zusammengestellt werden:

    [​IMG]
    Optionen

    Bestellbeispiel 1:
    ito für einfaches Pressure-Profiling (Preinfusion)*, unsichtbar, ohne PID-Funktion

    Bestellbeispiel 2:
    ito für einfaches Pressure-Profiling (Preinfusion)* und PID-Funktion, ohne Display aber mit Drehencoder zum Verstellen der Temperatur

    Bestellbeispiel 3:
    ito als sichtbarer PID mit Display, incl. einfachem Pressure Profiling (Preinfusion)*

    Bestellbeispiel 4:
    ito für volles Pressure-Profiling (mit Drucksensor und Display) aber ohne PID-Funktion

    Bestellbeispiel 5:
    ito für volles Pressure-Profiling (mit Drucksensor) und PID-Funktion - mit Display

    Silvia-User sollten die orange LED-Lampe im Shop hinzufügen, Gaggia Classic-User das vertikale Display wählen (Type "V").

    *: Installationen ohne Drucksensor reichen für "Aufbau eines niedrigen Drucks" und tendenzielles Pressure-Profiling der Art "irgendwie fallender Druck" - nicht für reproduzierbare, exakte Druckprofile.


    BESTELLUNG

    Bestelle bei Software & Circuits, durch Klick auf eine Beispielkonfiguration. Du erhältst am nächsten Tag ein Angebot. Die Bestellannahme endet am 25. März oder bei Ausverkauf der Produktionskapazität. Danach sind bis zur nächsten Produktion keine Bestellungen möglich.

    Ablauf

    Nach der Bestellphase werden die Bauteile bestellt. Diverse Komponenten werden aus China geliefert. Das ist zeitlich kaum planbar, da die Verzögerungen bei Post/Zoll schwanken. Ich setze 6 Wochen ab dem 26. März an, was bedeutet, dass alle Komponenten für die eigentliche Produktion bis Mitte Mai eingetroffen sein sollten. Der voraussichtliche Auslieferungstermin wäre ca. 10 Tage später. Alle Angaben vorbehaltlich der Belieferung durch Vorlieferanten und insoweit unverbindlich.


    Haftung

    Ich biete elektronische Bauteile an. Der unprogrammierte Mikrocontroller wird bei Dir zum PID, indem Du ihn in eine 230V-Espressomaschine einbaust und Firmware aufspielt. Für diese Schritte übernehme ich weder Haftung noch Gewährleistung: Basteln in Espressomaschinen erfolgt auf eigenes Risiko & Haftung.
     
  2. #2 faustino, 20.03.2019
    faustino

    faustino Mitglied

    Dabei seit:
    03.03.2010
    Beiträge:
    2.392
    Zustimmungen:
    1.911
    ito is a microcontroller with 2-4 solid-state relays, Wifi and optional on-board 230V power supply (web site; video). ito can be turned into a pressure and temperature controller by flashing the free leva! firmware. leva! brings many innovative functions to manual espresso machines: Perfect brewing temperature (PID), real pressure profiling with pressure sensor, preinfusion, dosing, shortened warm-up, shot timer, shot counter, tank monitoring, scale monitoring, energy-saving functions and much more.

    [​IMG]
    65x56mm: ito occupies less space than credit cards

    [​IMG]
    Display (optional) in top lid of a machine; custom lid manufactured via laser-cutting service

    VISIBLE | INVISIBLE

    Although leva! is best used with a display (rotary encoder = pressure regulator), a display is not required. The menus can be accessed wirelessly with a Virtual Display app:

    [​IMG]
    Virtual Display (for Windows, Linux, Mac OS X, Android)

    A machine with leva! can look as it did before adding ito. Only an optional rotary encoder might indicate the presence of ito (to adjust the temperature without a computer; could be discreetly installed on the rear side). Optionally, for better signalling, a white LED can be inserted into the original heating lamp.

    Bluetooth Low Energy | Weighing and Dosing

    The optional Bluetooth module (BLE 5) can connect ito to a scale (Skale 2) and other devices.

    [​IMG]
    Bluetooth Low Energy-Erweiterung

    OPTIMIZED FOR ESPRESSO

    Since leva! was developed for espresso machines, temperature control is better than with normal PID controllers: There is a feed-forward component that reacts to the flowmeter; the brewing temperature curve can be programmed during the shot; there are parameterizable coefficients (i.e. the PID can be configured differently for special situations: warm-up, standby, shot). For beginners, autotuning is included, which finds automatic settings. leva! can control two heating elements, e.g. a boiler and a brewing group. It amounts to two PIDs in one device. leva! contains a pressure control feature with pressure sensor feedback control loop and offers pressure profiling via programs, paddle or encoder.

    [​IMG]
    leva!'s pressure profiling can create pressure curves similar to those of lever machines

    SOFTWARE | CONFIGURE MONITOR IMPROVE

    Internal values and plots are transmitted live and wirelessly to a computer or tablet, making configuration a pleasure:

    [​IMG]
    The status monitor shows what happens - under Windows (Video), Linux, Mac OS X and Android (Video)

    DOCUMENTATION

    leva! is comprehensively documented on 228 pages (English), ito on 63 pages (English).

    [​IMG]
    Manuals are contained in the leva! download

    TSIC PRECISION

    leva! supports fast-responding TSic precision temperature sensors, which have 0.1°C resolution and are factory-calibrated. Maximum absolute error at 90°C is 0.3°C - better than Pt100 DIN B. The measuring range extends up to 150°C. Thermal adhesive is included for installing the sensor at the optimal position.

    FEATURES AT A GLANCE

    The following table compares leva! to typical entry-level industry PID controllers:

    [​IMG]

    INSTALLATION

    ito is installed with self-adhesive PCB feet. Depending on whether leva! is to be used as a PID, for pressure profiling, or both, the wiring changes are as simple as for any other PID (re-route 4 cables in the 230V wiring harness: power supply and thermostat) or siginificantly more demanding. The installation may only be carried out by qualified persons who can handle mains voltage and understands the English documentation.

    [​IMG]
    Installation with adhesive feet and acrylic insulation shield

    [​IMG]
    In the "engine room" of a Rabcilio Silvia

    The optional display can be installed behind a laser-cut (price at laserteileonline.de approx. 25€), behind a milled aluminium bezel (Schaeffer AG) or behind a 3D-printed nylon bezel.

    REQUIREMENTS

    leva! can be used with espresso machines in which a 'normal' PID could be installed. Temperature must not exceed 60°C at the place of installation (70°C at display). ito occupies 71x62mmx25mm, incl. feet. Leads are 40cm long. The external relay's dimensions are 56x41x26mm. It is installed with a heat-conducting adhesive pad. The flowmeter has 41mm diameter. leva!'s pump functions are designed for vibration pumps. Other pump types are not compatible. Programs that start the pump (e.g. dosing) do not work with manually operated grouphead valves (e.g. E61 levers). Further requirements and restrictions can be found in the ito introduction and the leva! manual. A Windows/Linux computer with Wifi is required at least once, to flash firmware (XP 32bit, Win7 32bit, Win8.1 64bit, Win10 64bit or Linux Mint 17.3 XFCE; other versions may also work, but have not been tested, so no guaranteed). A DVD drive is required. ito may not be compatible with every Wifi device (tested Wifi stick: TL-WN722N).

    OPTIONS DESIGNED FOR EXPANSION

    Components can be selected/combined according to the desired application:

    [​IMG]

    Ordering example 1:
    ito for simple pressure profiling (preinfusion)*, invisible, without PID function

    Ordering example 2:
    ito for simple pressure profiling (preinfusion)* and PID function, without display but with rotary encoder to adjust temperature

    Ordering example 3:
    ito as visible PID with display, incl. simple pressure profiling (preinfusion)*

    Ordering example 4:
    ito for full pressure profiling (with pressure sensor and display) but without PID function

    Ordering example 5:
    ito for full pressure profiling (with pressure sensor) and PID function - with display

    Notes: Silvia users should add the orange LED lamp in the shop. Gaggia Classic users should choose the non-standard vertical display (type "V").

    *: Installations without pressure sensor are sufficient for preinfusion of the type "pressure build-up up to some low pressure" and simple pressure profiling of the type "somehow falling pressure" - but not for repeatable, exact pressure profiles.


    ORDERING

    ito is available at Software & Circuits - go there by clicking on a sample configuration. You will receive an offer on the next workday. Order acceptance ends on 25/Mar or when the production capacity is sold out. After that, ordering will not be possible until the next production date.

    After the ordering phase, the components will be sourced. Various components come from China. The duration of this phase can not be planned exactly, as the delays in shipping and customs vary. I estimate 6 weeks after 26/Mar, which means that all components for the actual production should have arrived in early May. The expected delivery date would be about 10 days later. All details are subject to timely delivery by suppliers and are therefore non-binding.


    Liability

    I offer electronic components. You turn the unprogrammed microcontroller into a PID by installing it in a 230V espresso machine and flashing PID firmware. For these steps, I will neither accept legal resonsibility nor offer warranty: Modifiying your espresso machines happens at your own risk and legal responsibility.
     
  3. Maaka

    Maaka Mitglied

    Dabei seit:
    23.04.2019
    Beiträge:
    4
    Zustimmungen:
    0
    Hallo Kaffee-Netz-Freunde,

    Freunde des guten Espresso und Liebhaber des ito-Kits.

    Ich möchte sehr gerne meine aktuelle Bestellung (April-Mai) abgeben, sie war für eine Rancilio Silvia geplant. Diese hat leider das zeitliche gesegnet und ich bin auf einen Zweikreiser aufgestiegen.

    Nun ist meine aktuelle Bestellung über, diese möchte ich sehr gerne auf diesem Wege anbieten. Der liebe Faustino, liefert dann direkt an euch aus, sobald die Produktion etc. abgeschlossen ist.

    Zusätzlich biete ich den Membran-Regler-Komplettsatz, wie bei leva beschrieben (Membran-Regler inkl. Klammer, PTFE-Schlauch, Legris...) an.

    Meine Konfiguration

    Die Abwicklung bitte über eine private Nachricht.
     
Thema:

(( ito )) Produktion Apr-Mai

Die Seite wird geladen...

(( ito )) Produktion Apr-Mai - Ähnliche Themen

  1. [Verkaufe] Xenia 3o3 - Produktionsvorbereitung 2024

    Xenia 3o3 - Produktionsvorbereitung 2024: [ATTACH] Es wird nach einer sehr langen Phase der Optimierungen Zeit, die Maschine in die Produktion zu bringen. Das Ziel war das noch in 2023 zu...
  2. [Verkaufe] (( ito )) Produktion Nov 23

    (( ito )) Produktion Nov 23: ito ist ein Mikrocontroller mit SSR-Relais, WLAN und on-board-Netzteil (Über ito, Video). Durch Aufspielen der freien leva!-Firmware wird ito zum...
  3. [Verkaufe] (( ito )) Produktion Dezember - Januar

    (( ito )) Produktion Dezember - Januar: ito ist ein Mikrocontroller mit 2-4 SSR-Relais, WLAN und optional on-board Stromversorgung (Über ito, Video). Durch Aufspielen der freien...
  4. [Verkaufe] (( ito )) Produktion Okt/Nov

    (( ito )) Produktion Okt/Nov: ito ist ein Mikrocontroller mit 2-4 SSR-Relais, WLAN und optional on-board Stromversorgung (Über ito, Video). Durch Aufspielen der freien...
  5. [Verkaufe] (( ito )) Produktion Aug - Okt 2022

    (( ito )) Produktion Aug - Okt 2022: ito ist ein Mikrocontroller mit 2-4 SSR-Relais, WLAN und optional on-board Stromversorgung (Über ito, Video). Durch Aufspielen der freien...